Fix Wrong Wallet Balance

If you are staking and "you hit a stake," then the UTXO which hit the stake will become immature for a 101 confirmations, and the BLOCK in that UTXO will not be included in your Available Balance while it is immature. However, that UTXO will still be part of your Total Balance. Also, if you are using the BlockDX to sell BLOCK from your Blocknet wallet, the BLOCK balance in your wallet can temporarily drop by more than the amount of BLOCK you are selling. This can happen if your wallet's smallest available UTXO is larger than the amount of BLOCK you are selling in the transaction.

In both of the cases mentioned above, your total available balance will automatically return to the expected value after a short time. However, for various reasons, the Blocknet Wallet can occasionally display the wrong balance for an extended time, in which case you'll need to Recover Transactions from the blockchain before it will display the correct balance. You can confirm if your wallet needs a Recover Transactions operation as follows:

  1. Select Window->Coin Control to display the addresses (and UTXOs) where funds are stored in your wallet:

    Coin Control

    This will display a screen like this (in Tree mode): Coin Control

    Note: If using the Command Line Interface (CLI) to the wallet, you can get the same information as above by issuing the listunspent command from the directory where your blocknet-cli program is stored, like this:

    ./blocknet-cli listunspent
    You can also issue listunspent from Tools->Debug Console in the GUI/Qt wallet.

  2. Use the Blocknet Explorer to explore the addresses displayed under Coin Control.

  3. The total BLOCK available at each address as displayed in Coin Control (or listunspent) should match the total BLOCK available at each address as displayed by the Blocknet Explorer. If they don't match, you can sync your wallet address balances with the blockchain as described below in Recover Transactions:

Recover Transactions

There are several options to Recover Transactions and sync you wallet balance with the blockchain:

Option 1: From the GUI/Qt interface"

From the GUI/Qt interface

From the GUI/Qt wallet, select Tools->Wallet Repair->Recover Transactions(Drop metadata): Tools Wallet Repair Recover This will cause your wallet to close and restart.

Bug: Sometimes, especially if it takes a long time for your wallet to close, this operation attempts to restart the wallet too quickly and you'll see a message saying: Can't get a lock. If this happens, simply restart the wallet and try once again to perform Tools->Wallet Repair->Recover Transactions(Drop metadata).

Option 2: Add zapwallettxes=2 to blocknet.conf file, then restart wallet.

Add zapwallettxes=2 to blocknet.conf file, then restart wallet.

This option can be used with either GUI/Qt wallet or CLI wallet. The easiest way to edit your blocknet.conf file is as follows:

  1. Select Blocknet->Preferences:


  2. Click Open Configuration File:

    Open Config File

  3. Click OK to dismiss the warning:

    Open Config File

This will open the blocknet.conf file in your default editor.

An alternate way to edit your blocknet.conf file is to locate it in your Blocknet data directory, right-click (trackpad two-finger click) on the file, select Open With, then open it with a simple editor (e.g. NotePad on Windows, TextEdit on Mac). The data directory where blocknet.conf is found is as follows:

  • Windows
    Or paste %appdata%\Roaming\Blocknet\ into the File Explorer path field.
  • MacOS
    ~/Library/Application Support/Blocknet/
    Open Finder and in the Go menu select Go to Folder... and enter the above path.
  • Linux

Once you have your blocknet.conf file open in an editor, simply add the following line to the file:


Then save the file and restart your Blocknet wallet.

After your Blocknet wallet has finished syncing, remove the zapwallettxes=2 line from your blocknet.conf and save the file again. This will prevent your wallet from recovering all transactions from the blockchain every time you open it.

Option 3: Open Blocknet wallet with the parameter, -zapwallettxes=2

Open Blocknet wallet with the parameter, -zapwallettxes=2

This option can be used if you are starting the Blocknet wallet from the command line and passing a parameter. Close your Blocknet wallet, then open it from the directory where blocknet-qt or blocknetd is located, like this:

./blocknet-qt -zapwallettxes=2 
./blocknetd -zapwallettxes=2 

XRouter Beta Released!
Required Wallet Update! View downloads...